15 Oct
2020
15 Oct
'20
8:18 a.m.
New findings:
After a while the device gets unresponsive with thisnode.info but responds
at the ip address of anygw (10.236.0.1)
moreover dmesg:
[ 34.041779] batman_adv: bat0: The MTU of interface eth0_252 is too small
(1496) to handle the transport of batman-adv packets. Packets going over
this interface will be fragmented on layer2 which could impact the
performance. Setting the MTU to 1532 would solve the problem.
[ 34.066138] batman_adv: bat0: Interface activated: eth0_252
[ 38.885984] SQUASHFS error: xz decompression failed, data probably
corrupt
[ 38.892962] SQUASHFS error: squashfs_read_data failed to read block
0x17c8b2
I changed the MTU but I think this has nothing to do with this error
Am Di., 13. Okt. 2020 um 19:36 Uhr schrieb Juergen Kimmel <
juergenkimmel(a)gmail.com>gt;:
Situation has changed for whatever reason.
Now I have two Picostations meshing, one connected to a router
There is no wan interface visible from luci, but both have internet
Ifconfig
eth0 Link encap:Ethernet HWaddr DC:9F:DB:0B:17:CA
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:4
So one Picostation acts as gateway but is not configured as such
network:
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
config interface 'lan'
option type 'bridge'
option proto 'static'
option ip6assign '60'
option netmask '255.255.0.0'
option mtu '1500'
option ip6addr 'fdec:9fee:f1aa::ca17:b00/64'
option ipaddr '10.236.23.202'
list ifname 'bat0'
list ifname 'eth0'
config interface 'bat0'
option proto 'batadv'
option bridge_loop_avoidance '1'
option multicast_mode '0'
option distributed_arp_table '0'
option gw_mode 'client'
config device 'lm_net_br_lan_anygw_dev'
option type 'macvlan'
option name 'anygw'
option ifname 'br-lan'
option macaddr 'aa:aa:aa:ec:9f:aa'
config interface 'lm_net_br_lan_anygw_if'
option ifname 'anygw'
option auto '1'
option netmask '255.255.0.0'
option proto 'static'
option ipaddr '10.236.0.1'
option ip6addr 'fdec:9fee:f1aa::1/64'
config rule6 'lm_net_anygw_rule6'
option src 'fdec:9fee:f1aa::1/128'
option lookup '170'
config route6 'lm_net_anygw_route6'
option interface 'lm_net_br_lan_anygw_if'
option target 'fdec:9fee:f1aa::/64'
option table '170'
config rule 'lm_net_anygw_rule4'
option src '10.236.0.1/32'
option lookup '170'
config route 'lm_net_anygw_route4'
option interface 'lm_net_br_lan_anygw_if'
option target '10.236.0.0'
option netmask '255.255.0.0'
option table '170'
config device 'lm_net_eth0_batadv_dev'
option type '8021ad'
option name 'eth0_252'
option ifname 'eth0'
option vid '252'
option macaddr '02:95:39:0b:17:ca'
option mtu '1496'
config interface 'lm_net_eth0_batadv_if'
option auto '1'
option ifname 'eth0_252'
option proto 'batadv_hardif'
option master 'bat0'
config device 'lm_net_eth0_babeld_dev'
option type '8021ad'
option name 'eth0_17'
option ifname 'eth0'
option vid '17'
option mtu '1496'
config interface 'lm_net_eth0_babeld_if'
option auto '1'
option ifname 'eth0_17'
option proto 'static'
option ipaddr '10.236.23.202'
option netmask '255.255.255.255'
config interface 'lm_net_wlan0_mesh'
option proto 'none'
option mtu '1536'
option auto '1'
config device 'lm_net_wlan0_mesh_batadv_dev'
option type '8021ad'
option name 'wlan0-mesh_252'
option ifname '@lm_net_wlan0_mesh'
option vid '252'
option mtu '1532'
config interface 'lm_net_wlan0_mesh_batadv_if'
option auto '1'
option ifname 'wlan0-mesh_252'
option proto 'batadv_hardif'
option master 'bat0'
config device 'lm_net_wlan0_mesh_babeld_dev'
option type '8021ad'
option name 'wlan0-mesh_17'
option ifname '@lm_net_wlan0_mesh'
option vid '17'
config interface 'lm_net_wlan0_mesh_babeld_if'
option auto '1'
option ifname 'wlan0-mesh_17'
option proto 'static'
option ipaddr '10.236.23.202'
option netmask '255.255.255.255'
Am Mo., 12. Okt. 2020 um 16:57 Uhr schrieb Ilario Gelmetti <
iochesonome(a)gmail.com>gt;:
Hi!
Some comments in line:
On 10/11/20 2:38 PM, Juergen Kimmel wrote:
Powered by LuCI openwrt-19.07 branch
(git-20.247.75781-0d0ab01)
<https://github.com/openwrt/luci> / LiMe master development (master
rev.
7181c3b 20200927_1250)
Picostation connected to the router is no longer accessible via wifi.
This is weird.
The Picostation M2 is not emitting any accessible network via wifi?
It could be a RAM problem: Ubiquiti Picostation *2 have just 32 MB of
RAM memory.
Connect via ethernet cable and check the dmesg command output, looking
for any "out of memory OOM kill" message.
In order to have less memory usage you can disable the web interface
(LuCI or lime-app) with:
/etc/init.d/uhttpd disable
and reboot.
In case the problem was not a RAM limitation, please upload somewhere
the output of the lime-report command or, if you don't have the
lime-report command, the content of:
/etc/config/wireless
/etc/config/network
and the output of the commands:
wifi status
iwinfo
Obviously the internet access is not detected and
no wan interface is
configured.
lime-hwd-openwrt-wan and check-internet are installed I thought they
would do some kind of magic here.
This is normal instead: both vendor and OpenWrt recognize the only
ethernet port of Ubiquiti Picostation as LAN (not as WAN).
What the lime-hwd-openwrt-wan package is designed to do is: check if
OpenWrt would use an ethernet port as WAN, if positive, configure that
port as WAN.
In this case, OpenWrt use the port as LAN and thus lime-hwd-openwrt-wan
does not do anything.
In these cases what you have to write is an interface-specific
configuration in /etc/config/lime-node as documented here:
https://github.com/libremesh/lime-packages/blob/e572b4531b2fdcc89965974e0b2…
Something like this should be enough:
config net mywan
option linux_name 'eth0'
list protocols 'wan'
Regards
Jürgen
Let us know how it goes!
Ciao,
Ilario
--
Ilario
iochesonome(a)gmail.com
ilario(a)sindominio.net
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users