lime December 2020

lime-users@lists.libremesh.org

8 participants
23 discussions

by amuza

Hi, A node is connected to Internet gateway A, but it also has access to Internet gateway B. If gateway A fails, how long does it take to start using gateway B?

3 years

[lime-users] received packet on bat0 with own address as source address

by Juergen Kimmel

My syslog is flooded with the message above. Looking around I found in batctl o the same mac as originator as the next hop. root@da88:~# batctl o [B.A.T.M.A.N. adv openwrt-2019.2-7, MainIF/MAC: wlan1-mesh_252/78:a3:51:16:da:88 (bat0/7e:30:a4:a8:83:a9 BATMAN_IV)] Originator last-seen (#/255) Nexthop [outgoingIF] * 02:95:39:16:d9:ec 0.010s (239) 02:13:f2:16:d9:ec [eth0-2_252] * 02:95:39:16:d9:e8 2.180s (202) 02:13:f2:16:d9:ec [eth0-2_252] * 02:95:39:16:d9:48 0.660s (189) 02:13:f2:16:d9:ec [eth0-2_252] * 02:13:f2:16:d9:ec 0.010s (238) 02:13:f2:16:d9:ec [eth0-2_252] * dc:9f:db:0a:15:34 1.420s (193) 02:13:f2:16:d9:ec [eth0-2_252] May this be the reason? -- Regards Jürgen Kimmel

3 years, 3 months

[lime-users] APE522II Hardware restart was requested

by Juergen Kimmel

LiMe master development (master rev. d4b8732 20201210_2003) / LuCI openwrt-19.07 branch git-20.341.57626-51f55b5 This happens sometimes when accessing the nodes webui (only one node of three) [13503.728170] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [13503.733970] mt76x2e 0000:01:00.0: Build: 1 [13503.738240] mt76x2e 0000:01:00.0: Build Time: 201507311614____ [13503.751667] mt76x2e 0000:01:00.0: Firmware running! [13503.757335] ieee80211 phy0: Hardware restart was requested [13505.411576] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [13505.417290] mt76x2e 0000:01:00.0: Build: 1 [13505.421569] mt76x2e 0000:01:00.0: Build Time: 201507311614____ [13505.435799] mt76x2e 0000:01:00.0: Firmware running! [13505.442058] ieee80211 phy0: Hardware restart was requested -- Regards Juergen

3 years, 3 months

[lime-users] Performance APE522II

by Juergen Kimmel

LiMe master development (master rev. d4b8732 20201210_2003) / LuCI openwrt-19.07 branch git-20.341.57626-51f55b5 Poor performance from node to gateway measured by Lime-App metriks (1 Mb/sec) Ping: 64 bytes from wiki-01.infra.openwrt.org (139.59.209.225): icmp_req=3 ttl=50 time=151 ms (DUP!) 64 bytes from wiki-01.infra.openwrt.org (139.59.209.225): icmp_req=3 ttl=50 time=152 ms (DUP!) 64 bytes from wiki-01.infra.openwrt.org (139.59.209.225): icmp_req=3 ttl=50 time=154 ms (DUP!) 64 bytes from wiki-01.infra.openwrt.org (139.59.209.225): icmp_req=3 ttl=50 time=160 ms (DUP!) Despite (pointing to gateway): Mesh Point "LiMe" (wlan0-mesh) 78:A3:51:16:D9:ED 10.236.217.236 -72 dBm 30.0 Mbit/s, 40 MHz, VHT-MCS 0, VHT-NSS 2, Short GI 162.0 Mbit/s, 40 MHz, VHT-MCS 8, VHT-NSS 1-- Mesh Point "LiMe" (wlan1-mesh) 78:A3:51:16:D9:EC d9ec.thisnode.info (10.236.217.236, fe80::7aa3:51ff:fe16:d9ec) -60 dBm 115.6 Mbit/s, 20 MHz, MCS 13, Short GI 28.9 Mbit/s, 20 MHz, MCS 9, Short GI Regards Juergen

3 years, 3 months

[lime-users] Fwd: GSoC 2021 - update your project ideas!

by Ilario Gelmetti

---------- Forwarded message ---------- From: Andreas Bräu via gsoc-students-2019 <gsoc-students-2019(a)freifunk.net> Date: Dec 26, 2020 16:43 Subject: [gsoc-students-2019] GSoC 2021 - update your project ideas! To: gsoc-students-2019(a)freifunk.net Cc: Andreas Bräu <ab(a)andi95.de> > Hi there, > > I hope you all had a nice and quiet Christmas time. As I said in my last > email, we plan to apply again as organization for Google Summer of Code > 2021. > > The application period starts at January 29. See the full timeline here: > https://summerofcode.withgoogle.com/how-it-works/#timeline > > To prepare our application, we need your help! As in the years before, > we have to provide a nice list of ideas. Our ideas are listed at > https://projects.freifunk.net and can be edited there at > https://github.com/freifunk/projects.freifunk.net-contents > > We want you to review and update existing ideas, and of course add your > latest new ideas to the list. > Please keep in mind that Google changed some program rules: the > projects are smaller and the time frames more flexible. Find more > information at > https://google.github.io/gsocguides/mentor/defining-a-project-ideas-list > > If you have any questions, please don't hesitate to ask us. > > Best regards, > > Andi and Bluse > -- > gsoc-students-2019 mailing list > gsoc-students-2019(a)freifunk.net > https://lists.freifunk.net/mailman/listinfo/gsoc-students-2019-freifunk.net

3 years, 3 months

Re: [lime-users] BMX6 Graph

by amuza

Ilario Gelmetti: > > On Aug 26, 2020 19:02, amuza <amuza(a)riseup.net> wrote: >> How could I see through the command line other active nodes? > > This is a super important question and I'm not sure if the Babeld case have been documented anywhere yet, thanks for asking this! > For the neighbours known by Batman-adv you can use the command: > > batctl o > > For the neighbours (and much other info) known by Babeld you can use: > > echo dump | nc ::1 30003 > > Which sends a packet with the word "dump" to the same router at a door configured in /etc/config/babeld (if I remember correctly...) and shows the answer. > Ciao, > Ilario > I keep mising that very nice BMX6 graph Luci had on LiMe 17.06. I get very mcuh lost without it. What does the following command exactly do? batctl o I would like to understand its output. Thank you!

3 years, 3 months

[lime-users] firstbootwizard

by Juergen Kimmel

LiMe master development (master rev. 19cc376 20201215_2028) Hi, compiled with firstbootwizard selected but ubus-fbw inadvertently deselected. Then I installed ubus-fbw via opkg which broke the image, device not accessible anymore. Then I compiled ubus-fbw also selected, device not accessible. The reason for trying firstbootwizard is having the possibility to configure the community mesh name without changing any file. -- Regards Juergen

3 years, 4 months

Re: [lime-users] Lime-app

by Ilario Gelmetti

Hi Juergen! I have very limited experience with FirstBootWizard and lime-app. I basically used them just to check that they do not fail terribly but not much more. SAn, Marcos Gutierrez and German Ferrero (who I hope are reading this mailing list) are the ones who really know how those tools work or not work... Ciao! Ilario On Dec 16, 2020 11:22, Juergen Kimmel <juergenkimmel(a)gmail.com> wrote: > > Hi Ilario, > is your opinion still valid? > > I read this: > The LibreMesh team is happy to announce a new version of LibreMesh, 2020.1 "ExpansiveEmancipation" > * first-boot-wizard, an optional helper to deploy and extend the network that is well integrated with the LimeApp. > > On the other hand selecting firstbootwizard and ubus-fbw breaks the image > > Regards > Juergen > > Am So., 13. Dez. 2020 um 22:28 Uhr schrieb Ilario Gelmetti <iochesonome(a)gmail.com>: >> >> On 12/13/20 12:37 PM, Juergen Kimmel wrote: >> > But without FirstBootWizard It's not possible to configure the network?? >> >> lime-app has limited configuration capabilities (intentionally), an >> attempt of list of lime-app features can be found at >> https://github.com/libremesh/lime-packages/issues/327 >> >> If you want to have full access to configuration you'll have to access >> the router using SSH, add configuration lines in /etc/config/lime-node >> and apply it with "lime-config" command. >> >> The documentation for /etc/config/lime-node is on the documentation of >> the website: >> https://libremesh.org/docs/ >> and in the lime-example.txt file which can be found online at >> https://github.com/libremesh/lime-packages/blob/master/packages/lime-docs/f… >> or on the router at >> /docs/lime-example.txt >> and >> http://thisnode.info/docs/lime-example.txt >> >> If you cannot connect to the router using SSH, check out the >> documentation on the website: >> https://libremesh.org/docs/en_connecting_nodes.html >> and >> https://libremesh.org/docs/en_troubleshooting.html >> >> Ciao! >> Ilario >> >> >> _______________________________________________ >> lime-users mailing list >> lime-users(a)lists.libremesh.org >> https://lists.libremesh.org/mailman/listinfo/lime-users

3 years, 4 months

[lime-users] Lime-app

by Juergen Kimmel

Does lime-app depend always on firstbootwizard? -- Regards Juergen

3 years, 4 months

Re: [lime-users] LibreMesh 2020.1 ExpansiveEmancipation release

by Ilario Gelmetti

On 12/15/20 9:44 AM, ignifugo wrote: > On 15/12/20 05:19, SAn via lime-users wrote: >> The LibreMesh team is happy to announce a new version of LibreMesh, 2020.1 "ExpansiveEmancipation". >> Three years of work, 882 commits, 23 developers, tons of bug fixes and improvements! > Cold be really nice, have a publish place where is possible give a > feedback of the users/communities about the update and the result... Yesssss that would be great! What do you propose? > I'll write sure in our blog, after I'll pass the link. Nice :D Thanks! Hugs, Ilario

3 years, 4 months

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

lime December 2020