30 Nov
2016
30 Nov
'16
6:38 p.m.
Hi all,
got 5 of this dualband CPE (MT7620a). Tried QMP firmware, flash ok but
crashes only by accessing internet.
Anybody here got those working?
30 Nov
30 Nov
7:34 p.m.
2016-11-30 19:38 GMT+01:00 Juergen Kimmel <juergenkimmel(a)gmail.com>om>:
Hi all,
got 5 of this dualband CPE (MT7620a). Tried QMP firmware, flash ok but
crashes only by accessing internet.
Anybody here got those working?
It is not supported by last OpenWrt stable, so it's not yet supported
by LibreMesh (you could try with the develop branch).
Looks supported by both OpenWrt trunk and LEDE trunk.
Did you try with these?
8:37 p.m.
I tried with qMp trunk, no problem flashing, configuration produced some
headache but I went along. But afterwards probing internet access or even
lan access results in crashes. Sometimes devices recovered sometimes had to
be rebooted. Being a Noob I assume the lightest load leads to crash. There
are quite a lot error messages in the system log which I can't interprete.
What I read from the log there could be a Vlan problem as well as automatic
configuration of the wlan's fails at some point.
Ilario <iochesonome(a)gmail.com> schrieb am Mi., 30. Nov. 2016 um 20:35 Uhr:
2016-11-30 19:38 GMT+01:00 Juergen Kimmel
<juergenkimmel(a)gmail.com>om>:
Hi all,
got 5 of this dualband CPE (MT7620a). Tried QMP firmware, flash ok but
crashes only by accessing internet.
Anybody here got those working?
It is not supported by last OpenWrt stable, so it's not yet supported
by LibreMesh (you could try with the develop branch).
Looks supported by both OpenWrt trunk and LEDE trunk.
Did you try with these?
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
24 Dec
24 Dec
7:15 a.m.
Eventually I tried to compile ramips.
So "make info" shows no mt7620 but here
https://github.com/libremesh/lime-build/blob/16.07/targets/mt7620
How come?
Juergen Kimmel <juergenkimmel(a)gmail.com> schrieb am Mi., 30. Nov. 2016 um
21:37 Uhr:
I tried with qMp trunk, no problem flashing, configuration produced some
headache but I went along. But afterwards probing internet access or even
lan access results in crashes. Sometimes devices recovered sometimes had to
be rebooted. Being a Noob I assume the lightest load leads to crash. There
are quite a lot error messages in the system log which I can't interprete.
What I read from the log there could be a Vlan problem as well as automatic
configuration of the wlan's fails at some point.
Ilario <iochesonome(a)gmail.com> schrieb am Mi., 30. Nov. 2016 um 20:35 Uhr:
2016-11-30 19:38 GMT+01:00 Juergen Kimmel <juergenkimmel(a)gmail.com>om>:
Hi all,
got 5 of this dualband CPE (MT7620a). Tried QMP firmware, flash ok but
crashes only by accessing internet.
Anybody here got those working?
It is not supported by last OpenWrt stable, so it's not yet supported
by LibreMesh (you could try with the develop branch).
Looks supported by both OpenWrt trunk and LEDE trunk.
Did you try with these?
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
7:19 a.m.
Maybe a stupid question:
It is possible to add Lime to an existing Openwrt just by adding Lime repo
to the opkg config?
Juergen Kimmel <juergenkimmel(a)gmail.com> schrieb am Sa., 24. Dez. 2016 um
08:15 Uhr:
Eventually I tried to compile ramips.
So "make info" shows no mt7620 but here
https://github.com/libremesh/lime-build/blob/16.07/targets/mt7620
How come?
Juergen Kimmel <juergenkimmel(a)gmail.com> schrieb am Mi., 30. Nov. 2016 um
21:37 Uhr:
I tried with qMp trunk, no problem flashing, configuration produced some
headache but I went along. But afterwards probing internet access or even
lan access results in crashes. Sometimes devices recovered sometimes had to
be rebooted. Being a Noob I assume the lightest load leads to crash. There
are quite a lot error messages in the system log which I can't interprete.
What I read from the log there could be a Vlan problem as well as
automatic configuration of the wlan's fails at some point.
Ilario <iochesonome(a)gmail.com> schrieb am Mi., 30. Nov. 2016 um 20:35 Uhr:
2016-11-30 19:38 GMT+01:00 Juergen Kimmel <juergenkimmel(a)gmail.com>om>:
Hi all,
got 5 of this dualband CPE (MT7620a). Tried QMP firmware, flash ok but
crashes only by accessing internet.
Anybody here got those working?
It is not supported by last OpenWrt stable, so it's not yet supported
by LibreMesh (you could try with the develop branch).
Looks supported by both OpenWrt trunk and LEDE trunk.
Did you try with these?
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
12:34 p.m.
2016-12-24 8:19 GMT+01:00 Juergen Kimmel <juergenkimmel(a)gmail.com>om>:
It is possible to add Lime to an existing Openwrt just
by adding Lime repo
to the opkg config?
Yes it is!!
It is the "legacy way".
Refer to lime-packages readme file (remember to select the needed LiMe
packages from menuconfig):
https://github.com/libremesh/lime-packages/blob/develop/README.md
Eventually I tried to compile ramips.
So "make info" shows no mt7620 but here
https://github.com/libremesh/lime-build/blob/16.07/targets/mt7620
How come?
Yep, known issue, solved in develop branch.
https://github.com/libremesh/lime-build/issues/14
You can just copy the targets.mk file from develop branch.
25 Dec
25 Dec
5:59 a.m.
Ilario, can you help me further?
How should the opkg.config look like?
I could not fnd out how to use menuconfig
My test device is loaded with lede image and working
Ilario <iochesonome(a)gmail.com> schrieb am Sa., 24. Dez. 2016 um 13:34 Uhr:
2016-12-24 8:19 GMT+01:00 Juergen Kimmel <juergenkimmel(a)gmail.com>om>:
It is possible to add Lime to an existing Openwrt just
by adding Lime repo
to the opkg config?
Yes it is!!
It is the "legacy way".
Refer to lime-packages readme file (remember to select the needed LiMe
packages from menuconfig):
https://github.com/libremesh/lime-packages/blob/develop/README.md
Eventually I tried to compile ramips.
So "make info" shows no mt7620 but here
https://github.com/libremesh/lime-build/blob/16.07/targets/mt7620
How come?
Yep, known issue, solved in develop branch.
https://github.com/libremesh/lime-build/issues/14
You can just copy the targets.mk file from develop branch.
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
11:38 p.m.
2016-12-25 6:59 GMT+01:00 Juergen Kimmel <juergenkimmel(a)gmail.com>om>:
Ilario, can you help me further?
How should the opkg.config look like?
My test device is loaded with lede image and working
Ah! Sorry, I didn't get the question, so, well I don't know how to use
opkg.config file...
I expected to find compiled LiMe packages for mt7620 in
http://downloads.libremesh.org/develop/
but there's nothing for mt7620
@p4u, any thought? Is this normal?
Anyway, compiling locally libremesh with develop branch of lime-build
you will have the packages you need in the output/*/packages folder.
Installing them one by one could be tedious because of dependencies.
Setting up a opkg repo could be an option but I never tried.
Consider reflashing with a LiMe image already including everything...
I could not fnd out how to use menuconfig
This suggestion I gave you was based on the misunderstanding that you
were compiling LiMe starting from a LEDE base. (anyway also in
lime-build you can access menuconfig for advanced packages selection)
2686
days inactive
2711
days old
lime-users@lists.libremesh.org
7 comments
2 participants
participants (2)
-
Ilario -
Juergen Kimmel