15 Apr
2016
15 Apr
'16
4:27 p.m.
Hi everyone, I've spent the past few weeks trying to find routers without
blocked firmware and test small deployments of Libre-Mesh. First off, are
there any online tutorials / walkthroughs on installation? I'm basing
everything off one workshop I went to.
I'm at the point now where I have a two Ubiquity airGateways and one
airRouter flashed with builds from here <
http://chef.altermundi.net/downloads/libre-mesh/r44952/1509/ar71xx/>gt;. They
are able to broadcast the Libre-Mesh and Libre-Mesh/routerID SSIDs.
But I'm unable to open the router settings. Since I've flashed, I haven't
been able to access any router using any of the following: 192.168.0.1,
192.168.1.1, thisnode.info or http://anygw.
Any tips about what steps I can take next to debug what's going on? I have
no prior experience with Libre-Mesh or OpenWRT so you may have to speak
very slowly to me. Thanks,
marvin
27 Apr
27 Apr
9:13 a.m.
2016-04-15 18:27 GMT+02:00 Marvin Arnold <marvin(a)unplugged.im>im>:
Hi everyone, I've spent the past few weeks trying
to find routers without
blocked firmware and test small deployments of Libre-Mesh. First off, are
there any online tutorials / walkthroughs on installation? I'm basing
everything off one workshop I went to.
Hi Marvin! Sorry for the delay!!
Up to now there's first flashing guide for Libre-Mesh, as it's
suggested to follow the generic OpenWrt guide for flashing:
https://wiki.openwrt.org/doc/howto/generic.flashing
and the OpenWrt instructions for specific devices:
https://wiki.openwrt.org/toh/start
I'm sorry for this lack of documentation on Libre-Mesh side, if you
will to write one on the wiki... :D
I'm at the point now where I have a two Ubiquity
airGateways and one
airRouter flashed with builds from here
<http://chef.altermundi.net/downloads/libre-mesh/r44952/1509/ar71xx/>.
Perfect! That's the right Libre-Mesh stable firmware source.
They
are able to broadcast the Libre-Mesh and Libre-Mesh/routerID SSIDs.
Ok :)
But I'm unable to open the router settings. Since
I've flashed, I haven't
been able to access any router using any of the following: 192.168.0.1,
192.168.1.1, thisnode.info or http://anygw.
Mmmh I supposed that both thisnode.info or http://anygw should work...
Did you try to connect to the Libre-Mesh router disconnecting your PC
from any other network?
Both via cable and via wireless?
The IP of the Libre-Mesh router is set in a way to not have
collisions, so it's quite random.
For discovering the router IPv4 and IPv6 and IPv6 link local you have
many ways on Linux (wireshark, netdiscover, ping6 ff02::1%interface,
arp-scan, nmap). I heard about an Android app also (Fing). On other
operating systems no idea.
Also on this point we should write a wiki page...
Any tips about what steps I can take next to debug
what's going on? I have
no prior experience with Libre-Mesh or OpenWRT so you may have to speak very
slowly to me.
Just connect to the router and try to discover it's IP first, then we'll see :)
Bye!
Ilario
1 May
1 May
6:02 p.m.
Thanks Ilario,
All of a sudden I'm having some success with http://anygw
I'm happy to take notes on my experience and add it to the blog. I'm having
some trouble registering though.
https://libre-mesh.org/account/register
After registration, I don't get any confirmation email and
username/password not accepted when I try to log in.
On Wed, Apr 27, 2016 at 4:13 AM, Ilario <iochesonome(a)gmail.com> wrote:
2016-04-15 18:27 GMT+02:00 Marvin Arnold
<marvin(a)unplugged.im>im>:
Hi everyone, I've spent the past few weeks
trying to find routers without
blocked firmware and test small deployments of Libre-Mesh. First off, are
there any online tutorials / walkthroughs on installation? I'm basing
everything off one workshop I went to.
Hi Marvin! Sorry for the delay!!
Up to now there's first flashing guide for Libre-Mesh, as it's
suggested to follow the generic OpenWrt guide for flashing:
https://wiki.openwrt.org/doc/howto/generic.flashing
and the OpenWrt instructions for specific devices:
https://wiki.openwrt.org/toh/start
I'm sorry for this lack of documentation on Libre-Mesh side, if you
will to write one on the wiki... :D
I'm at the point now where I have a two
Ubiquity airGateways and one
airRouter flashed with builds from here
<http://chef.altermundi.net/downloads/libre-mesh/r44952/1509/ar71xx/>.
Perfect! That's the right Libre-Mesh stable firmware source.
They
are able to broadcast the Libre-Mesh and Libre-Mesh/routerID SSIDs.
Ok :)
But I'm unable to open the router settings.
Since I've flashed, I haven't
been able to access any router using any of the following: 192.168.0.1,
192.168.1.1, thisnode.info or http://anygw.
Mmmh I supposed that both thisnode.info or http://anygw should work...
Did you try to connect to the Libre-Mesh router disconnecting your PC
from any other network?
Both via cable and via wireless?
The IP of the Libre-Mesh router is set in a way to not have
collisions, so it's quite random.
For discovering the router IPv4 and IPv6 and IPv6 link local you have
many ways on Linux (wireshark, netdiscover, ping6 ff02::1%interface,
arp-scan, nmap). I heard about an Android app also (Fing). On other
operating systems no idea.
Also on this point we should write a wiki page...
Any tips about what steps I can take next to
debug what's going on? I
have
no prior experience with Libre-Mesh or OpenWRT so
you may have to speak
very
slowly to me.
Just connect to the router and try to discover it's IP first, then we'll
see :)
Bye!
Ilario
_______________________________________________
users mailing list
users(a)lists.libre-mesh.org
https://lists.libre-mesh.org/mailman/listinfo/users
11 p.m.
On 05/01/2016 08:02 PM, Marvin Arnold wrote:
All of a sudden I'm having some success with
http://anygw
Great :D
De-associating from other connections always helps :)
I'm happy to take notes on my experience and add
it to the blog. I'm
having some trouble registering though.
https://libre-mesh.org/account/register
After registration, I don't get any confirmation email and
username/password not accepted when I try to log in.
If I remember correctly this problem is present since toooo loong time,
maybe Libre-Mesh devs (now at Battlemesh in Porto) can solve this?
Ciao!
Ilario
--
Ilario Gelmetti
iochesonome(a)gmail.com
igelmetti(a)iciq.es
ilario.gelmetti(a)estudiants.urv.cat
21 Jun
21 Jun
6:36 p.m.
I finally figured out how to get consistent access to my Ubiquiti devices,
through 10.187.0.1. Could someone explain to me what's going on? Why would
I be able to access it there and not through http://anygw and why in
particular 10.187.0.1. Note that I'm using a version of LiMe that's a bit
old so this may no longer be an issue.
On Sun, May 1, 2016 at 6:00 PM, Ilario Gelmetti <iochesonome(a)gmail.com>
wrote:
On 05/01/2016 08:02 PM, Marvin Arnold wrote:
All of a sudden I'm having some success with
http://anygw
Great :D
De-associating from other connections always helps :)
I'm happy to take notes on my experience and
add it to the blog. I'm
having some trouble registering though.
https://libre-mesh.org/account/register
After registration, I don't get any confirmation email and
username/password not accepted when I try to log in.
If I remember correctly this problem is present since toooo loong time,
maybe Libre-Mesh devs (now at Battlemesh in Porto) can solve this?
Ciao!
Ilario
--
Ilario Gelmetti
iochesonome(a)gmail.com
igelmetti(a)iciq.es
ilario.gelmetti(a)estudiants.urv.cat
_______________________________________________
users mailing list
users(a)lists.libre-mesh.org
https://lists.libre-mesh.org/mailman/listinfo/users
2864
days inactive
2931
days old
lime-users@lists.libremesh.org
4 comments
3 participants
participants (3)
-
Ilario -
Ilario Gelmetti
-
Marvin Arnold