22 May
2014
22 May
'14
6:36 a.m.
----- Mensaje original -----
Mesh+AP+Client works as long as they're on the same channel. (it
works
currently with our OLSR setup).
Great, so have no problem to work with MX6+BATMAN-adv setup :)
Ok, so if you can get a successful connection for yourself, you can announce the default
route with bmx6. There's some ways, but I think is better that Gioacchino or anybody
with more technical experience than me, say best way.
That's my /etc/config/lime (i.e. you can change "option primary_dev"):
----
config lime 'network'
option primary_dev 'eth0'
list vlans '10'
list protos 'bmx6'
list protos 'batadv'
option ipv4_net '192.168.11.0/24'
option ipv6_net '2a00:1508:1:f820::/64'
config lime 'wireless'
option ssid 'garraflliure.guifi.net'
option mesh_bssid 'ca:fe:00:c0:ff:ee'
option mesh_mcast_rate_2ghz '24000'
option mesh_mcast_rate_5ghz '6000'
list mesh_channel_2ghz '11'
list mesh_channel_2ghz '1'
list mesh_channel_5ghz '36+'
----
In uci you have:
lime.network.primary_dev
(and other lime.network.*)
When you success manually, we can take a look to think the module :)
[1] http://ca.wiki.guifi.net/wiki/Unsolclic (sorry catalan only, summary: list of commands
(more or less "automatic generated") to configure a device just copying &
pasting in shell, in this case (based on OpenWrt) is a list of uci commands).
De: "Ramiro Polla"
<ramiro.polla(a)gmail.com>
Para: "libre-mesh developement" <dev(a)lists.libre-mesh.org>
Enviados: Miércoles, 21 de Mayo 2014 18:43:04
Asunto: Re: [lime-dev] I have installed the firmware. Now what? =)
Hi,
2014-05-21 6:17 GMT-03:00 Gioacchino Mazzurco
<gmazzurco89(a)gmail.com>om>:
Gioacchino is right. I have supported it in Libre-mesh, but with justoneclick (guifi.net
style[1]), not just by default. Sorry. But this is planned to be supported by default.
On Tuesday 20 May 2014 23:29:21 Ramiro Polla
wrote:
Hm, I'm confused now. Al says it's supported but you're saying it
isn't. (I haven't tested yet) Currently we use OpenWRT+OLSR and a complicated
configuration, I'd
like to replace that with a better and easier to use solution. I
have
no problem using the command line to connect, but we want more
people
to adopt this, and that way they'd need to do it with a simpler
interface. That's why I thought about using libre-mesh as a base
system.
Yeah you can use this as base system you simply need to develop a
lime module
that does that for you, start finding a little but meningful name
something
like lime-* (look at other lime module name for inspiration)
And if you can do it by your self with shell of course you will be
able to
develop a lime module in lua, that integrate with lime ecosistem
So ethernet is shared by default, but how would I
configure
another
source for sharing?
What you mean by sharing ethernet? If you mean sharing an internet
connection
available trought ethernet it is in plan but not implemented yet (a 3g/4g
modem,
Yet another module you can implement (I have no time for this now)
another wireless adapter
Yet another module you can implement (I have no time for this now)
or even
the same wifi acting as mesh+AP)
I doubt this is doable, but it it is, or if i am misunderstanding
here it goes
the mantra Yet another module you can implement (I have no
time for this now)
;)
I understand I can add modules to implement things. That is not the
issue. See below.
[...]
this is still not implemented yet, so at moment
you need to
configure manually
a node to connect to the internet and annource the default route
with bmx6
So it seems that after I get a successful connection, I have to
announce the default route with bmx6. This is probably what I am
looking for. Where can I get more information related to this and
libre-mesh's current setup?