16 Sep
2014
16 Sep
'14
2:36 p.m.
I would need to test the images in my routers to reproduce your problem. However I've
a lot of work to do these days and I'll be disconnected during this week, so I cannot
help you now, sorry.
@Others, please help Gabriel :)
On 16/09/14 16:16, gabriel giovaniello wrote:
I tried with your new firmware upload but same issue,
libremesh not appear
at boot, i need to shutdown and start wifi with physical button and i can
connect to wifi LiMe without being kicked.
For testing purposes i will use firmware as is.
Is any command-line i can use to do the same as wifi on/off with physical
button?
I’m thinking about startup command so can work without intervention.
Sorry for being so noob.
On Tuesday, September 16, 2014, gabriel giovaniello <gabrielgio(a)gmail.com>
wrote:
--
Gabriel H. Giovaniello
+54 2216230146
--
./p4u
Excellent!
I will try right now.
I Sept 13 compilation i found that if i shutdown wifi with physical
button of
WR841ND and start again, appears libremesh network and Lime
network (before libremesh was not there) and i’m not kicked from wifi.
So to be clear i will describe what i do and
results:
1) flashed
2) connect with cable to lan and successfully receive IP
3) Connect another device from wifi and i receive IP but i’m disconnected
about 20
seconds.
Log mention something about MTU i tried to change but still error there.
If i shutdown wifi on router with wifi on/off button and start wifi again.
In my wifi networks appears libremesh (before was not there) and i can
connect
without kick.
Here i attach Kernel Log of Sep 13 compilation, hope this help to figure
out what
happened:
[ 0.000000] Linux version 3.10.49
(lime@qmpbuild) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r41825) ) #230
Sat Sep 13 13:54:27 CEST 2014
[ 0.000000] MyLoader: sysp=ab02aeab,
boardp=a2abaaa2, parts=aa22aaaa
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 rev 1
[ 0.000000] Clocks: CPU:550.000MHz, DDR:399.389MHz, AHB:199.694MHz,
Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802fca90, node_mem_map
81000000
[ 0.000000] Normal zone: 64 pages used for
memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way,
VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768
alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total
pages: 8128
[ 0.000000] Kernel command line:
board=TL-WR841N-v9
console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128
(order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Inode-cache hash table entries:
2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28848k/32768k available (2202k kernel code, 3920k
reserved,
561k data, 244k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3,
MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.050000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] MIPS: machine is TP-LINK TL-WR841N/ND v9
[ 0.490000] bio: create slab <bio-0> at 0
[ 0.490000] Switching to clocksource MIPS
[ 0.500000] NET: Registered protocol family 2
[ 0.500000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.510000] TCP bind hash table entries: 512
(order: -1, 2048 bytes)
[ 0.520000] TCP: Hash tables configured (established 512 bind 512)
[ 0.520000] TCP: reno registered
[ 0.520000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.530000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.540000] NET: Registered protocol family 1
[ 0.540000] PCI: CLS 0 bytes, default 32
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY)
(c) 2001-2006 Red Hat, Inc.
[ 0.570000] msgmni has been set to 56
[ 0.580000] io scheduler noop registered
[ 0.580000] io scheduler deadline registered (default)
[ 0.590000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.610000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a
16550A
[ 0.620000] console [ttyS0] enabled,
bootconsole disabled
[ 0.630000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.640000] m25p80 spi0.0: found s25sl032p, expected m25p80
[ 0.650000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[ 0.650000] 5 tp-link partitions found on MTD device spi0.0
[ 0.660000] Creating 5 MTD partitions on "spi0.0":
[ 0.660000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.670000] 0x000000020000-0x000000119a70 : "kernel"
[ 0.680000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.690000] 0x000000119a70-0x0000003f0000 :
"rootfs"
[ 0.700000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.710000] mtd: device 2 (rootfs) set to be
root filesystem
[ 0.720000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.720000] 0x000000380000-0x0000003f0000 : "rootfs_data"
[ 0.730000] 0x0000003f0000-0x000000400000 : "art"
[ 0.740000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.770000] libphy: ag71xx_mdio: probed
[ 1.320000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.360000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.920000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04
[uid=004dd042, driver=Generic PHY]
[ 2.930000] eth1: Atheros AG71xx at
0xb9000000, irq 4, mode:MII
[ 2.940000] TCP: cubic registered
[ 2.940000] NET: Registered protocol family 17
[ 2.940000] Bridge firewalling registered
[ 2.950000] 8021q: 802.1Q VLAN Support v1.8
[ 2.960000] VFS: Mounted root (squashfs filesystem) readonly on device
31:2.
[ 2.970000] Freeing unused kernel memory: 244K
(80313000 - 80350000)
[ 8.360000] eth0: link up (1000Mbps/Full duplex)
[ 10.020000] jffs2: notice: (306) jffs2_build_xattr_subsystem: complete
building
xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 22 of
xref (0 dead, 2 orphan) found.
[ 10.060000] eth0: link down
[ 11.450000] NET: Registered protocol family 10
[ 11.460000] tun: Universal TUN/TAP device driver, 1.6
[ 11.460000] tun: (C) 1999-2004 Max Krasnyansky <maxk(a)qualcomm.com>
[ 11.480000] nf_conntrack version 0.5.0 (454 buckets, 1816 max)
[ 11.500000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.530000] batman_adv: B.A.T.M.A.N. advanced 2014.2.0 (compatibility
version
15) loaded
[ 11.550000] Loading modules backported from
Linux version
master-2014-05-22-0-gf2032ea
[ 11.560000] Backport generated by
backports.git
backports-20140320-37-g5c33da0
[ 11.600000] Ebtables v2.0 registered
[ 11.600000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.670000] xt_time: kernel timezone is -0000
[ 11.710000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.710000] cfg80211: World regulatory domain updated:
[ 11.720000] cfg80211: DFS Master region: unset
[ 11.720000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain,
max_eirp), (dfs_cac_time)
[ 11.730000] cfg80211: (2402000 KHz - 2472000
KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.740000] cfg80211: (2457000 KHz - 2482000
KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.750000] cfg80211: (2474000 KHz - 2494000
KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.760000] cfg80211: (5170000 KHz - 5250000
KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.770000] cfg80211: (5735000 KHz - 5835000
KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 11.770000] cfg80211: (57240000 KHz -
63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 11.970000] ath: EEPROM regdomain: 0x0
[ 11.970000] ath: EEPROM indicates default country code should be used
[ 11.970000] ath: doing EEPROM country->regdmn map search
[ 11.970000] ath: country maps to regdmn code: 0x3a
[ 11.970000] ath: Country alpha2 being used: US
[ 11.970000] ath: Regpair used: 0x3a
[ 12.000000] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[ 12.010000] ieee80211 phy0: Atheros AR9531
Rev:1 mem=0xb8100000, irq=2
[ 12.020000] cfg80211: Calling CRDA for country: US
[ 12.030000] cfg80211: Regulatory domain changed to country: US
[ 12.030000] cfg80211: DFS Master region: unset
[ 12.040000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain,
max_eirp), (dfs_cac_time)
[ 12.050000] cfg80211: (2402000 KHz - 2472000
KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 12.050000] cfg80211: (5170000 KHz - 5250000
KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 12.060000] cfg80211: (5250000 KHz - 5330000
KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 12.070000] cfg80211: (5735000 KHz - 5835000
KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 12.080000] cfg80211: (57240000 KHz -
63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 20.570000] IPv6: ADDRCONF(NETDEV_UP): eth0:
link is not ready
[ 20.570000] device eth0 entered promiscuous mode
[ 20.680000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.740000] device br-lan entered promiscuous mode
[ 20.740000] IPv6: ADDRCONF(NETDEV_UP): anygw: link is not ready
[ 20.760000] IPv6: ADDRCONF(NETDEV_UP): eth0-13: link is not ready
[ 20.810000] IPv6: ADDRCONF(NETDEV_UP): eth0-154: link is not ready
[ 20.870000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 21.910000] eth0: link up (1000Mbps/Full duplex)
[ 21.910000] br-lan: port 1(eth0) entered forwarding state
[ 21.920000] br-lan: port 1(eth0) entered forwarding state
[ 21.920000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.950000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 21.950000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0-13: link becomes ready
[ 21.960000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0-154: link becomes ready
[ 21.970000] IPv6: ADDRCONF(NETDEV_CHANGE): anygw: link becomes ready
[ 22.200000] batman_adv: bat0: Adding interface: eth0-154
[ 22.200000] batman_adv: bat0: The MTU of interface eth0-154 is too
small (1496)
to handle the transport of batman-adv packets. Packets going
over this interface will be fragmented on layer2 which could impact the
performance. Setting the MTU to 1532 would solve the problem.
[ 22.230000] batman_adv: bat0: Interface
activated: eth0-154
[ 22.250000] 8021q: adding VLAN 0 to HW filter on device bat0
[ 22.250000] device bat0 entered promiscuous mode
[ 22.260000] br-lan: port 2(bat0) entered forwarding state
[ 22.260000] br-lan: port 2(bat0) entered forwarding state
[ 22.560000] batman_adv: bat0: bridge_loop_avoidance: Changing from:
disabled
to: enabled
[ 22.560000] batman_adv: bat0:
distributed_arp_table: Changing from:
enabled to: disabled
[ 22.760000] IPv6: ADDRCONF(NETDEV_UP):
wlan0_adhoc: link is not ready
[ 22.790000] IPv6: ADDRCONF(NETDEV_UP): wlan0_adhoc-13: link is not
ready
[ 22.810000] IPv6: ADDRCONF(NETDEV_UP):
wlan0_adhoc-154: link is not
ready
[ 23.920000] br-lan: port 1(eth0) entered
forwarding state
[ 23.970000] IPv6: ADDRCONF(NETDEV_UP): wlan0_ap: link is not ready
[ 24.000000] device wlan0_ap entered promiscuous mode
[ 24.000000] br-lan: port 3(wlan0_ap) entered forwarding state
[ 24.010000] br-lan: port 3(wlan0_ap) entered forwarding state
[ 24.050000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0_ap: link becomes ready
[ 24.260000] br-lan: port 2(bat0) entered forwarding state
[ 24.430000] wlan0_adhoc: Created IBSS using preconfigured BSSID
ca:fe:00:c0:ff:ee
[ 24.440000] wlan0_adhoc: Creating new IBSS
network, BSSID
ca:fe:00:c0:ff:ee
[ 24.450000] IPv6: ADDRCONF(NETDEV_CHANGE):
wlan0_adhoc: link becomes
ready
[ 24.490000] IPv6: ADDRCONF(NETDEV_CHANGE):
wlan0_adhoc-13: link
becomes ready
[ 24.490000] IPv6: ADDRCONF(NETDEV_CHANGE):
wlan0_adhoc-154: link
becomes ready
[ 24.740000] batman_adv: bat0: Adding
interface: wlan0_adhoc-154
[ 24.750000] batman_adv: bat0: The MTU of interface wlan0_adhoc-154 is
too small
(1500) to handle the transport of batman-adv packets. Packets
going over this interface will be fragmented on layer2 which could impact
the performance. Setting the MTU to 1532 would solve the problem.
[ 24.780000] batman_adv: bat0: Interface
activated: wlan0_adhoc-154
[ 26.010000] br-lan: port 3(wlan0_ap) entered forwarding state
Regards and thank you for your support, i will flash new release and let
you know
what happened.
On Tuesday, September 16, 2014, Pau <pau(a)dabax.net> wrote:
> The alternative is to compile it yourself using lime-build or using a
raw
openwrt buildroot :)
>
> I've compiled new images, you can try them. I don't know the current
status of 14.08, Gui should know it better.
>
> The branch hardware-detection (which is compiling right now) should work
fine.
>
> @Devs, we must merge all these branches in a single one!
>
> On 16/09/14 15:51, gabriel giovaniello wrote:
>> Hi Paul, thank you for your support,
>> please let me know when i can download new images or if there is an
>> alternative, i tried chef from alter mesh but images seems to be old.
>>
>> Regards
>>
>> On Tuesday, September 16, 2014, Pau <pau(a)dabax.net> wrote:
>>> There is some problem in the downloads server, it looks like the
>> compilations are not correct. I'll check it.
>>>
>>> On 15/09/14 16:06, gabriel giovaniello wrote:
>>>> That is the full name:
>>>> TP-Link-TL-WR841N-v9-LiMe______-factory-20140913_1353
>>>>
>>>> I Also tried with a bullet m2 with this image:
>>>> Bullet-LiMe______-factory-20140913_1326
>>>>
>>>> both with same result.
>>>>
>>>> Last night about 3AM (i was trying to make it work), i found Up in
LOG (i
>>>> have not access now because i’m
outside) mention something about
wrong
>> MTU
>>>> in eth0-154 and wifiadhoc0-154 or something like that i need to
increase
>>>> MTU from 1368 to 1532.
>>>> Hope this helps.
>>>> I just installed firmware and with no config from my side i have this
>>>> errors.
>>>>
>>>> Regards and thank you for your support.
>>>>
>>>> On Monday, September 15, 2014, Ilario Gelmetti <
ilario.gelmetti(a)sns.it>
>>>> wrote:
>>>>> Il 15/09/2014 13:57, Gabriel Giovaniello ha scritto:
>>>>>> Hi Gui, this is URL:
>>>>>> http://downloads.libre-mesh.org/develop/
>>>>>>
>>>>>> I downloaded yesterday.
>>>>> So the image you downloaded contains "20140913" in the
filename?
>>>>> Could you check?
>>>>>
>>>>>> Also i receive a list of:
>>>>>> kern.warn kernel: [ 1479.000000] br-lan: received packet on bat0
with
>>>> own address as source address
>>>
>>> This error should have been solved long time ago... argh
>>>
>>>
>>>
>>>
>>
>>
>>
>> _______________________________________________
>> Dev mailing list
>> Dev(a)lists.libre-mesh.org
>> https://lists.libre-mesh.org/mailman/listinfo/dev
>>
>
> --
> ./p4u
>
>
--
./p4u