9 Nov
2016
9 Nov
'16
4:21 p.m.
On 09/11/16 00:56, Gui Iribarren wrote:
There's a group currently testing in Brasil how
does LibreMesh run on
these ath9k+ath10k routers.
ath9k = 2.4ghz
ath10k = 5ghz
Extra packets needed so far:
kmod-ath10k
ath10k-firmware-qca988x
Progress so far: adhoc doesn't seem to work (virtual interface is not
created) on the ath10k interface. The 2.4ghz interface works correctly
(it's ath9k)
adhoc confirmed not supported looking at "iw phy"
Currently trying ieee80211s mode on ath10k.
Will report any news
so, when trying to bring up the mesh interface, logread says
ath10k_pci 0000:01:00.0: must load driver with rawmode=1 to add mesh
interfaces
tried simply reloading the driver with rawmode=1, but then logread said
rawmode = 1 requires support from firmware
following this
https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
i downloaded this exact file
https://github.com/kvalo/ath10k-firmware/raw/master/QCA988X/hw2.0/10.2.4.70…
placed it the router
/lib/firmware/ath10k/QCA988X/hw2.0/firmware-5.bin
overwriting the one from the package ath10k-firmware-qca988x
then
# rmmod ath10k_pci ; rmmod ath10k_core
# insmod ath10k_core rawmode=1 ; insmod ath10k_pci
# wifi
and it came up :)
i had some issues with wireless.radioX.htmode=HT40, logread spits out
some errors during wifi reload
radio0 (24777): Usage: iw [options] dev <devname> set channel <channel>
[HT20|HT40+|HT40-]
radio0 (24777): Options:
radio0 (24777): --debug enable netlink debugging
looks like netifd is passing the parameters wrong to "iw"
according again to this
https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
the syntax is supposed to be "iw mesh0 set freq 5180 80 5210"
and it looks like netifd is doing the classical "iw mesh0 set channel 48
HT40+"
for the meantime, i just unset htmode, and it everything comes up fine
(albeit slow, a netperf between the two nodes on the same table gives
only ~20 mbps, it could be around ~100 mbps if properly configured)
anyway this thread will turn definitely "lime-dev", and offtopic for
lime-users, so I'm moving the discussion there :)
If anyone has already tested this hardware or has any tips, much welcome :)
cheers!
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
9 Nov
9 Nov
4:44 p.m.
New subject: [lime-users] Testing LibreMesh 16.07 on TPLink AC1750
On 09/11/16 17:21, Gui Iribarren wrote:
On 09/11/16 00:56, Gui Iribarren wrote:
Thank you so much Pau for always being so stubborn about the
"ieee80211s" mode support in libremesh, insisting it would be better
supported than adhoc in the future :) you were right!
in few words, I managed to get LibreMesh working on an 802.11ac
equipment, using ath10k and ieee80211s
now, what about ath10k stability? Well, that's left as an exercise for
the brasilian team :)
There's a group currently testing in Brasil
how does LibreMesh run on
these ath9k+ath10k routers.
ath9k = 2.4ghz
ath10k = 5ghz
Extra packets needed so far:
kmod-ath10k
ath10k-firmware-qca988x
Progress so far: adhoc doesn't seem to work (virtual interface is not
created) on the ath10k interface. The 2.4ghz interface works correctly
(it's ath9k)
adhoc confirmed not supported looking at "iw phy"
Currently trying ieee80211s mode on ath10k.
Will report any news
so, when trying to bring up the mesh interface, logread says
ath10k_pci 0000:01:00.0: must load driver with rawmode=1 to add mesh
interfaces
tried simply reloading the driver with rawmode=1, but then logread said
rawmode = 1 requires support from firmware
following this
https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
i downloaded this exact file
https://github.com/kvalo/ath10k-firmware/raw/master/QCA988X/hw2.0/10.2.4.70…
placed it the router
/lib/firmware/ath10k/QCA988X/hw2.0/firmware-5.bin
overwriting the one from the package ath10k-firmware-qca988x
then
# rmmod ath10k_pci ; rmmod ath10k_core
# insmod ath10k_core rawmode=1 ; insmod ath10k_pci
# wifi
and it came up :)
i had some issues with wireless.radioX.htmode=HT40, logread spits out
some errors during wifi reload
radio0 (24777): Usage: iw [options] dev <devname> set channel <channel>
[HT20|HT40+|HT40-]
radio0 (24777): Options:
radio0 (24777): --debug enable netlink debugging
looks like netifd is passing the parameters wrong to "iw"
according again to this
https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
the syntax is supposed to be "iw mesh0 set freq 5180 80 5210"
and it looks like netifd is doing the classical "iw mesh0 set channel 48
HT40+"
for the meantime, i just unset htmode, and it everything comes up fine
(albeit slow, a netperf between the two nodes on the same table gives
only ~20 mbps, it could be around ~100 mbps if properly configured) From that team, thanks especially to drebs! for
allowing me to remotely
login and try to brick their devices ;)
nice, very nice, after recreating the interface manually on both sides,
but using "VHT80" mode, i get ~100mbps
what follows are the manual steps,
i don't think there's anything to fix on "our" (LibreMesh) side to
properly support this; it's even possible that netifd from LEDE is
already fixed. so i'll just do one of my "horrible hacks" in chef
(overwriting the firmware file, and such) for the "rede Mocambos" to
progress ASAP.
iw phy phy0 interface add mesh0 type mp mesh_id LiMe
iw mesh0 set freq 5180 80 5210
ip l set up mesh0
iw mesh0 station dump
root@LiMe-09248f:~# netperf -cCD1 -Hfe80::32b5:c2ff:fe09:6034%mesh0
MIGRATED TCP STREAM TEST from :: (::) port 0 AF_INET6 to
fe80::32b5:c2ff:fe09:6034 () port 0 AF_INET6 : demo
Interim result: 91.69 10^6bits/s over 1.001 seconds ending at
1478709257.529
Interim result: 95.98 10^6bits/s over 1.002 seconds ending at
1478709258.532
Interim result: 96.33 10^6bits/s over 1.000 seconds ending at
1478709259.532
Interim result: 96.36 10^6bits/s over 1.001 seconds ending at
1478709260.533
Interim result: 96.26 10^6bits/s over 1.001 seconds ending at
1478709261.534
Interim result: 95.60 10^6bits/s over 1.006 seconds ending at
1478709262.540
Interim result: 96.91 10^6bits/s over 1.001 seconds ending at
1478709263.541
Interim result: 97.17 10^6bits/s over 1.001 seconds ending at
1478709264.542
Interim result: 96.97 10^6bits/s over 1.002 seconds ending at
1478709265.543
Interim result: 96.74 10^6bits/s over 0.994 seconds ending at
1478709266.538
Recv Send Send Utilization Service
Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local
remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.02 95.95 99.10 88.72 84.617
75.756
root@LiMe-09248f:~# iw mesh0 station dump
Station 30:b5:c2:09:60:34 (on mesh0)
inactive time: 920 ms
rx bytes: 4400805
rx packets: 37312
tx bytes: 130131582
tx packets: 84801
tx retries: 0
tx failed: 0
signal: -42 dBm
signal avg: -43 dBm
Toffset: 33792059 us
tx bitrate: 6.0 MBit/s
rx bitrate: 975.0 MBit/s VHT-MCS 7 80MHz short GI VHT-NSS 3
mesh llid: 7963
mesh plid: 60395
mesh plink: ESTAB
mesh local PS mode: ACTIVE
mesh peer PS mode: ACTIVE
mesh non-peer PS mode: ACTIVE
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
connected time: 29 seconds
anyway this thread will turn definitely "lime-dev", and offtopic for
lime-users, so I'm moving the discussion there :)
If anyone has already tested this hardware or has any tips, much welcome :)
cheers!
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
4:59 p.m.
New subject: [lime-users] Testing LibreMesh 16.07 on TPLink AC1750
Hey!
If i rembember well i have implemented 80211s support in libremsh long time
ago!!
https://github.com/libremesh/lime-packages/blob/develop/packages/lime-syste…
So no need of dirty stuff in chef!
Yeah I know you like dirty stuff :p
But no need this time just add ieee80211s to wifi modes and protos and it
should work like a charm (beware that this combination just use ieee80211s
like a smarter adhoc but don't use it for routing or other trickeris)
Baci!
On Wednesday 09 November 2016 17:44:33 Gui Iribarren wrote:
On 09/11/16 17:21, Gui Iribarren wrote:
On 09/11/16 00:56, Gui Iribarren wrote:
Thank you so much Pau for always being so stubborn about the
"ieee80211s" mode support in libremesh, insisting it would be better
supported than adhoc in the future :) you were right!
in few words, I managed to get LibreMesh working on an 802.11ac
equipment, using ath10k and ieee80211s
now, what about ath10k stability? Well, that's left as an exercise for
the brasilian team :)
From that team, thanks especially to drebs! for allowing me to remotely
login and try to brick their devices ;)
nice, very nice, after recreating the interface manually on both sides,
but using "VHT80" mode, i get ~100mbps
what follows are the manual steps,
i don't think there's anything to fix on "our" (LibreMesh) side to
properly support this; it's even possible that netifd from LEDE is
already fixed. so i'll just do one of my "horrible hacks" in chef
(overwriting the firmware file, and such) for the "rede Mocambos" to
progress ASAP.
iw phy phy0 interface add mesh0 type mp mesh_id LiMe
iw mesh0 set freq 5180 80 5210
ip l set up mesh0
iw mesh0 station dump
root@LiMe-09248f:~# netperf -cCD1 -Hfe80::32b5:c2ff:fe09:6034%mesh0
MIGRATED TCP STREAM TEST from :: (::) port 0 AF_INET6 to
fe80::32b5:c2ff:fe09:6034 () port 0 AF_INET6 : demo
Interim result: 91.69 10^6bits/s over 1.001 seconds ending at
1478709257.529
Interim result: 95.98 10^6bits/s over 1.002 seconds ending at
1478709258.532
Interim result: 96.33 10^6bits/s over 1.000 seconds ending at
1478709259.532
Interim result: 96.36 10^6bits/s over 1.001 seconds ending at
1478709260.533
Interim result: 96.26 10^6bits/s over 1.001 seconds ending at
1478709261.534
Interim result: 95.60 10^6bits/s over 1.006 seconds ending at
1478709262.540
Interim result: 96.91 10^6bits/s over 1.001 seconds ending at
1478709263.541
Interim result: 97.17 10^6bits/s over 1.001 seconds ending at
1478709264.542
Interim result: 96.97 10^6bits/s over 1.002 seconds ending at
1478709265.543
Interim result: 96.74 10^6bits/s over 0.994 seconds ending at
1478709266.538
Recv Send Send Utilization Service
Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local
remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.02 95.95 99.10 88.72 84.617
75.756
root@LiMe-09248f:~# iw mesh0 station dump
Station 30:b5:c2:09:60:34 (on mesh0)
inactive time: 920 ms
rx bytes: 4400805
rx packets: 37312
tx bytes: 130131582
tx packets: 84801
tx retries: 0
tx failed: 0
signal: -42 dBm
signal avg: -43 dBm
Toffset: 33792059 us
tx bitrate: 6.0 MBit/s
rx bitrate: 975.0 MBit/s VHT-MCS 7 80MHz short GI VHT-NSS 3
mesh llid: 7963
mesh plid: 60395
mesh plink: ESTAB
mesh local PS mode: ACTIVE
mesh peer PS mode: ACTIVE
mesh non-peer PS mode: ACTIVE
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
connected time: 29 seconds
There's a group currently testing in Brasil
how does LibreMesh run on
these ath9k+ath10k routers.
ath9k = 2.4ghz
ath10k = 5ghz
Extra packets needed so far:
kmod-ath10k
ath10k-firmware-qca988x
Progress so far: adhoc doesn't seem to work (virtual interface is not
created) on the ath10k interface. The 2.4ghz interface works correctly
(it's ath9k)
adhoc confirmed not supported looking at "iw phy"
Currently trying ieee80211s mode on ath10k.
Will report any news
so, when trying to bring up the mesh interface, logread says
ath10k_pci 0000:01:00.0: must load driver with rawmode=1 to add mesh
interfaces
tried simply reloading the driver with rawmode=1, but then logread said
rawmode = 1 requires support from firmware
following this
https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
i downloaded this exact file
https://github.com/kvalo/ath10k-firmware/raw/master/QCA988X/hw2.0/10.2.4.7
0/firmware-5.bin_10.2.4.70.6-2
placed it the router
/lib/firmware/ath10k/QCA988X/hw2.0/firmware-5.bin
overwriting the one from the package ath10k-firmware-qca988x
then
# rmmod ath10k_pci ; rmmod ath10k_core
# insmod ath10k_core rawmode=1 ; insmod ath10k_pci
# wifi
and it came up :)
i had some issues with wireless.radioX.htmode=HT40, logread spits out
some errors during wifi reload
radio0 (24777): Usage: iw [options] dev <devname> set channel <channel>
[HT20|HT40+|HT40-]
radio0 (24777): Options:
radio0 (24777): --debug enable netlink debugging
looks like netifd is passing the parameters wrong to "iw"
according again to this
https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
the syntax is supposed to be "iw mesh0 set freq 5180 80 5210"
and it looks like netifd is doing the classical "iw mesh0 set channel 48
HT40+"
for the meantime, i just unset htmode, and it everything comes up fine
(albeit slow, a netperf between the two nodes on the same table gives
only ~20 mbps, it could be around ~100 mbps if properly configured) anyway this thread will turn definitely
"lime-dev", and offtopic for
lime-users, so I'm moving the discussion there :)
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users If anyone has already tested this hardware or has
any tips, much welcome
:)
cheers!
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
5:17 p.m.
New subject: [lime-users] Testing LibreMesh 16.07 on TPLink AC1750
On 09/11/16 17:59, Gio wrote:
_______________________________________________ lime-users mailing
list lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
Hey!
If i rembember well i have implemented 80211s support in libremsh
long time ago!!
i know, i know,
the configuration created by lime is perfectly correct (with
proto=ieee80211s)
the problem is that netifd doesn't configure the interfaces optimally
and that the firmware bundled in the vanilla ath10k-firmware-qca988x
doesn't support mesh mode :(
so that's why i said there's nothing to fix in LiMe,
they are all problems of openwrt 15.05.1
at some point, we could make a LiMe release 16.07.1 to workaround the
problems,
but first i'll test everything in a single network in chef, and then we
can take that experience as a base
https://github.com/libremesh/lime-packages/blob/develop/packages/lime-syste…
So no need of dirty stuff in chef! Yeah I know you like dirty stuff
:p
But no need this time just add ieee80211s to wifi modes and protos
and it should work like a charm (beware that this combination just
use ieee80211s like a smarter adhoc but don't use it for routing or
other trickeris)
Baci!
On Wednesday 09 November 2016 17:44:33 Gui Iribarren wrote:
> On 09/11/16 17:21, Gui Iribarren wrote:
>> On 09/11/16 00:56, Gui Iribarren wrote:
>>> There's a group currently testing in Brasil how does LibreMesh
>>> run on these ath9k+ath10k routers.
>>>
>>> ath9k = 2.4ghz ath10k = 5ghz
>>>
>>> Extra packets needed so far:
>>>
>>> kmod-ath10k ath10k-firmware-qca988x
>>>
>>> Progress so far: adhoc doesn't seem to work (virtual interface
>>> is not created) on the ath10k interface. The 2.4ghz interface
>>> works correctly (it's ath9k)
>>
>> adhoc confirmed not supported looking at "iw phy"
>>
>>> Currently trying ieee80211s mode on ath10k. Will report any
>>> news
>>
>> so, when trying to bring up the mesh interface, logread says
>>
>> ath10k_pci 0000:01:00.0: must load driver with rawmode=1 to add
>> mesh
>>
>> interfaces
>>
>> tried simply reloading the driver with rawmode=1, but then
>> logread said
>>
>> rawmode = 1 requires support from firmware
>>
>> following this
>> https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
>>
>>
>>
i downloaded this exact file
0/firmware-5.bin_10.2.4.70.6-2
>>
>> placed it the router
>> /lib/firmware/ath10k/QCA988X/hw2.0/firmware-5.bin overwriting the
>> one from the package ath10k-firmware-qca988x
>>
>> then # rmmod ath10k_pci ; rmmod ath10k_core # insmod ath10k_core
>> rawmode=1 ; insmod ath10k_pci # wifi
>>
>> and it came up :)
>>
>> i had some issues with wireless.radioX.htmode=HT40, logread spits
>> out some errors during wifi reload
>>
>> radio0 (24777): Usage: iw [options] dev <devname> set channel
>> <channel>
>>
>> [HT20|HT40+|HT40-]
>>
>> radio0 (24777): Options: radio0 (24777): --debug enable netlink
>> debugging
>>
>> looks like netifd is passing the parameters wrong to "iw"
>> according again to this
>> https://github.com/o11s/open80211s/wiki/ath10k-(802.11ac)-for-Mesh-Support
>>
>>
the syntax is supposed to be "iw mesh0 set freq 5180 80 5210"
and it looks like netifd is doing the classical "iw mesh0 set
channel 48 HT40+"
for the meantime, i just unset htmode, and it everything comes up
fine (albeit slow, a netperf between the two nodes on the same
table gives only ~20 mbps, it could be around ~100 mbps if
properly configured)
Thank you so much Pau for always being so stubborn about the
"ieee80211s" mode support in libremesh, insisting it would be
better supported than adhoc in the future :) you were right!
in few words, I managed to get LibreMesh working on an 802.11ac
equipment, using ath10k and ieee80211s
now, what about ath10k stability? Well, that's left as an exercise
for the brasilian team :)
From that team, thanks especially to drebs! for allowing me to
remotely login and try to brick their devices ;)
nice, very nice, after recreating the interface manually on both
sides, but using "VHT80" mode, i get ~100mbps
what follows are the manual steps, i don't think there's anything
to fix on "our" (LibreMesh) side to properly support this; it's
even possible that netifd from LEDE is already fixed. so i'll just
do one of my "horrible hacks" in chef (overwriting the firmware
file, and such) for the "rede Mocambos" to progress ASAP.
iw phy phy0 interface add mesh0 type mp mesh_id LiMe iw mesh0 set
freq 5180 80 5210 ip l set up mesh0 iw mesh0 station dump
root@LiMe-09248f:~# netperf -cCD1
-Hfe80::32b5:c2ff:fe09:6034%mesh0 MIGRATED TCP STREAM TEST from ::
(::) port 0 AF_INET6 to fe80::32b5:c2ff:fe09:6034 () port 0
AF_INET6 : demo Interim result: 91.69 10^6bits/s over 1.001
seconds ending at 1478709257.529 Interim result: 95.98 10^6bits/s
over 1.002 seconds ending at 1478709258.532 Interim result: 96.33
10^6bits/s over 1.000 seconds ending at 1478709259.532 Interim
result: 96.36 10^6bits/s over 1.001 seconds ending at
1478709260.533 Interim result: 96.26 10^6bits/s over 1.001
seconds ending at 1478709261.534 Interim result: 95.60 10^6bits/s
over 1.006 seconds ending at 1478709262.540 Interim result: 96.91
10^6bits/s over 1.001 seconds ending at 1478709263.541 Interim
result: 97.17 10^6bits/s over 1.001 seconds ending at
1478709264.542 Interim result: 96.97 10^6bits/s over 1.002
seconds ending at 1478709265.543 Interim result: 96.74 10^6bits/s
over 0.994 seconds ending at 1478709266.538 Recv Send Send
Utilization Service Demand Socket Socket Message Elapsed
Send Recv Send Recv Size Size Size Time
Throughput local remote local remote bytes bytes bytes
secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.02 95.95 99.10 88.72
84.617 75.756 root@LiMe-09248f:~# iw mesh0 station dump Station
30:b5:c2:09:60:34 (on mesh0) inactive time: 920 ms rx bytes:
4400805 rx packets: 37312 tx bytes: 130131582 tx packets: 84801 tx
retries: 0 tx failed: 0 signal: -42 dBm signal avg: -43 dBm
Toffset: 33792059 us tx bitrate: 6.0 MBit/s rx bitrate: 975.0
MBit/s VHT-MCS 7 80MHz short GI VHT-NSS 3 mesh llid: 7963 mesh
plid: 60395 mesh plink: ESTAB mesh local PS mode: ACTIVE mesh peer
PS mode: ACTIVE mesh non-peer PS mode: ACTIVE authorized: yes
authenticated: yes preamble: long WMM/WME: yes MFP: no TDLS peer:
no connected time: 29 seconds
anyway this thread will turn definitely
"lime-dev", and offtopic
for lime-users, so I'm moving the discussion there :)
_______________________________________________ lime-users mailing
list lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users If anyone has already tested this hardware or has
any tips,
much welcome :)
cheers!
_______________________________________________ lime-users
mailing list lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
_______________________________________________ lime-users
mailing list lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
2729
days inactive
2729
days old
3 comments
2 participants
participants (2)
-
Gio -
Gui Iribarren