18 Nov
2016
18 Nov
'16
2:01 p.m.
Hello,
I did a sysupgrade of my Ubiquity Nanostation M, becaus I changed
country/region/place and I would like to setup libremesh here from scratch.
I created a new profile and used my cooked img, but somethings goes
wrong: Now I've just a red static led when it powers on.
There's something I can try before starting with the failsafe process [1] ?
https://wiki.openwrt.org/doc/howto/generic.failsafe
byez
--
ɐqɯ@s
19 Nov
19 Nov
12:38 a.m.
Did you do `sysupgrade -n`? Something similar happened to me before and
I was able to recover with failsafe or by creating a custom network
profile, http://libremesh.org/docs/troubleshooting.html
On 11/18/2016 08:01 AM, samba wrote:
Hello,
I did a sysupgrade of my Ubiquity Nanostation M, becaus I changed
country/region/place and I would like to setup libremesh here from scratch.
I created a new profile and used my cooked img, but somethings goes
wrong: Now I've just a red static led when it powers on.
There's something I can try before starting with the failsafe process [1] ?
https://wiki.openwrt.org/doc/howto/generic.failsafe
byez
6 p.m.
Do you have a NanoStation (old) or the new XW ? Take into account that
they are different models and require different firmwares!
On 19/11/16 01:38, Marvin Arnold wrote:
Did you do `sysupgrade -n`? Something similar happened
to me before and
I was able to recover with failsafe or by creating a custom network
profile, http://libremesh.org/docs/troubleshooting.html
On 11/18/2016 08:01 AM, samba wrote:
--
./p4u
Hello,
I did a sysupgrade of my Ubiquity Nanostation M, becaus I changed
country/region/place and I would like to setup libremesh here from scratch.
I created a new profile and used my cooked img, but somethings goes
wrong: Now I've just a red static led when it powers on.
There's something I can try before starting with the failsafe process [1] ?
https://wiki.openwrt.org/doc/howto/generic.failsafe
byez
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
21 Nov
21 Nov
12:09 p.m.
On 11/19/2016 04:00 PM, Pau wrote:
Do you have a NanoStation (old) or the new XW ? Take
into account that
they are different models and require different firmwares!
Hi Pau,
I used the nano-m5 firmware,
file: openwrt-15.05.1-ubnt-nano-m-r49403-caus-1607-sysupgrade.bin
but I don't know why, after flashing with the sysupgrade everything
fucks up.
Now I'm trying to enter in the failsafe mode, with no success.
As per the documentation [1] I'm doing the following:
* power off the router
* setup on my eth0 the ip: 192.168.1.2/24
* connect via lan to the router (in this case is PoE, but whatever)
* click the reset button, more than 10s - it reboots
* reboot the system, pressing reset again, but doesn't enter in failsafe
mode
* no udp packet sent via LAN
any ideas?
--
ɐqɯ@s
4:10 p.m.
When you do it through LuCi, there is a check box that is checked by
default. I don't remember exactly, but something like "save / import
existing configuration". You should uncheck that, this is equivalent to
using '-n' with sysupgrade.
I haven't used a NanoStation so no clue how to get into failsafe. Have
you tried the other instructions on the troubleshooting page, "Unable to
establish Ethernet connection"?
On 11/21/2016 06:09 AM, samba wrote:
On 11/19/2016 04:00 PM, Pau wrote:
Do you have a NanoStation (old) or the new XW ?
Take into account that
they are different models and require different firmwares!
Hi Pau,
I used the nano-m5 firmware,
file: openwrt-15.05.1-ubnt-nano-m-r49403-caus-1607-sysupgrade.bin
but I don't know why, after flashing with the sysupgrade everything
fucks up.
Now I'm trying to enter in the failsafe mode, with no success.
As per the documentation [1] I'm doing the following:
* power off the router
* setup on my eth0 the ip: 192.168.1.2/24
* connect via lan to the router (in this case is PoE, but whatever)
* click the reset button, more than 10s - it reboots
* reboot the system, pressing reset again, but doesn't enter in failsafe
mode
* no udp packet sent via LAN
any ideas?
4:24 p.m.
did you hold the reset button? in older models i remember, you kept the
reset button pressed until the leds (if any) began to blink in a pattern.
El 21/11/16 a las 11:10, Marvin Arnold escribió:
When you do it through LuCi, there is a check box that
is checked by
default. I don't remember exactly, but something like "save / import
existing configuration". You should uncheck that, this is equivalent to
using '-n' with sysupgrade.
I haven't used a NanoStation so no clue how to get into failsafe. Have
you tried the other instructions on the troubleshooting page, "Unable to
establish Ethernet connection"?
On 11/21/2016 06:09 AM, samba wrote:
--
Cordialmente
Leonardo Taborda Ángel
leonardotaborda(a)networkbogota.org
www.networkbogota.org
"When there is a will, there is a way"
On 11/19/2016 04:00 PM, Pau wrote:
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users Do you have a NanoStation (old) or the new XW ?
Take into account that
they are different models and require different firmwares!
Hi Pau,
I used the nano-m5 firmware,
file: openwrt-15.05.1-ubnt-nano-m-r49403-caus-1607-sysupgrade.bin
but I don't know why, after flashing with the sysupgrade everything
fucks up.
Now I'm trying to enter in the failsafe mode, with no success.
As per the documentation [1] I'm doing the following:
* power off the router
* setup on my eth0 the ip: 192.168.1.2/24
* connect via lan to the router (in this case is PoE, but whatever)
* click the reset button, more than 10s - it reboots
* reboot the system, pressing reset again, but doesn't enter in failsafe
mode
* no udp packet sent via LAN
any ideas?
11:53 a.m.
On 11/18/2016 10:38 PM, Marvin Arnold wrote:
Did you do `sysupgrade -n`? Something similar happened
to me before and
no, I uploaded the sysupgrade img from the web interface:
applied > reboot > broken
I was able to recover with failsafe or by creating a
custom network
profile, http://libremesh.org/docs/troubleshooting.html
thanks for the link I'll have a look
--
ɐqɯ@s
2952
days inactive
2955
days old
lime-users@lists.libremesh.org
6 comments
4 participants
participants (4)
-
Leonardo Taborda -
Marvin Arnold -
Pau -
samba