19 Apr
2017
19 Apr
'17
3:24 p.m.
On Wednesday 19 April 2017 15:52:08 IST Ruairi Hickey wrote:
On Wednesday 19 April 2017 16:34:05 IST Pau wrote:
Hi,
While the mesh appears to be up and the stations can see each other there
is no ip connectivity - if a client is connected to the libremesh.org via AP
node d9:18:6e it can connect to the internet / outside via AP d9:44:80. Are
there additional steps required to enable this (it works out of the box on ad-
hoc) ? Apologies if I am asking stupid questions.... this is new to me but
if I can assist in any way please let me know...
Thanks,
Ruairi
list modes 'ap'
list modes 'apname'
list modes 'ieee80211s'
option channel_2ghz '11'
option channel_5ghz '48'
Hi,
That seems to have worked OK.... I have a 3rd box at home which I will
test as well to try get all 3 on the mesh. The routers are 3 x TPLink TL-
WR841N.
iw dev wlan0-mesh station dump
Station 84:16:f9:d9:18:6e (on wlan0-mesh)
inactive time: 20 ms
rx bytes: 492473
rx packets: 7570
tx bytes: 270
tx packets: 3
tx retries: 0
tx failed: 0
signal: -19 [-20, -26] dBm
signal avg: -18 [-20, -22] dBm
Toffset: -335602982 us
tx bitrate: 6.5 MBit/s MCS 0
rx bitrate: 19.5 MBit/s MCS 2
mesh llid: 7348
mesh plid: 5441
mesh plink: ESTAB
mesh local PS mode: ACTIVE
mesh peer PS mode: ACTIVE
mesh non-peer PS mode: ACTIVE
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
connected time: 390 seconds
Thanks,
Ruairi
19 Apr
19 Apr
3:25 p.m.
New subject: [lime-users] 802.11s config
On Wednesday 19 April 2017 16:24:14 IST Ruairi Hickey wrote:
On Wednesday 19 April 2017 15:52:08 IST Ruairi Hickey
wrote:
On Wednesday 19 April 2017 16:34:05 IST Pau
wrote:
Hi,
While the mesh appears to be up and the stations can see each other
there is no ip connectivity - if a client is connected to the libremesh.org
via AP node d9:18:6e it can not connect to the internet / outside via AP
list modes 'ap'
list modes 'apname'
list modes 'ieee80211s'
option channel_2ghz '11'
option channel_5ghz '48'
Hi,
That seems to have worked OK.... I have a 3rd box at home which I
will
test as well to try get all 3 on the mesh. The routers are 3 x TPLink TL-
WR841N.
iw dev wlan0-mesh station dump
Station 84:16:f9:d9:18:6e (on wlan0-mesh)
inactive time: 20 ms
rx bytes: 492473
rx packets: 7570
tx bytes: 270
tx packets: 3
tx retries: 0
tx failed: 0
signal: -19 [-20, -26] dBm
signal avg: -18 [-20, -22] dBm
Toffset: -335602982 us
tx bitrate: 6.5 MBit/s MCS 0
rx bitrate: 19.5 MBit/s MCS 2
mesh llid: 7348
mesh plid: 5441
mesh plink: ESTAB
mesh local PS mode: ACTIVE
mesh peer PS mode: ACTIVE
mesh non-peer PS mode: ACTIVE
authorized: yes
authenticated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
connected time: 390 seconds
Thanks,
Ruairi sorry type ^^^ it can not connect
d9:44:80. Are there additional steps required to enable this (it works
out of the box on ad- hoc) ? Apologies if I am asking stupid
questions.... this is new to me but if I can assist in any way please let
me know...
Thanks,
Ruairi
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users 
5:29 p.m.
New subject: [lime-users] 802.11s config
On 04/19/2017 05:25 PM, Ruairi Hickey wrote:
While the mesh appears to be up and the stations can
see each other
there is no ip connectivity - if a client is connected to the libremesh.org
via AP node d9:18:6e it can not connect to the internet / outside via AP
d9:44:80.
Hi Ruairi!
Have you plugged an internet connection to a WAN port of your router?
If your router doesn't have a WAN port you will have to configure
another one as WAN (check out /etc/config/lime-example and
http://libremesh.org/docs/changing_network_behavior.html ).
If this doesn't work: can you post the content of /etc/config/network on
your LibreMesh router?
And the output of the "ip address show" commend.
Are there additional steps required to enable this (it
works
out of the box on ad- hoc) ?
No, it should automagically work when you plug the WAN port of the LiMe
router into a LAN port of a router offering a DHCP server and a gateway
to the internet.
Let us know!
Ilario
6:46 p.m.
New subject: [lime-users] 802.11s config
On Wednesday 19 April 2017 19:29:59 IST Ilario Gelmetti wrote:
On 04/19/2017 05:25 PM, Ruairi Hickey wrote:
Hi Ilario,
The WAN port is connected to the switch and if that is the only router in
up / or if I connect to that when connecting to SSID libremesh.org I can
connect to the internet.
If I connect to either of the other 2 nodes I cannot connect to the
Internet...
I've attached 2 text files (one for each router with the file contents)
router connected to switch (WAN port) / Internet
router-d94040.txt
router in mesh
router-d94480.txt
Thanks,
Ruairi
(if the attachments get stripped I'll resend with the contents inline..)
While the mesh appears to be up and the stations
can see each other
there is no ip connectivity - if a client is connected to the
libremesh.org
via AP node d9:18:6e it can not connect to the internet / outside via AP
d9:44:80.
Hi Ruairi!
Have you plugged an internet connection to a WAN port of your router?
If your router doesn't have a WAN port you will have to configure
another one as WAN (check out /etc/config/lime-example and
http://libremesh.org/docs/changing_network_behavior.html ).
If this doesn't work: can you post the content of /etc/config/network on
your LibreMesh router?
And the output of the "ip address show" commend.
Are there additional steps required to enable
this (it works
out of the box on ad- hoc) ?
No, it should automagically work when you plug the WAN port of the LiMe
router into a LAN port of a router offering a DHCP server and a gateway
to the internet.
Let us know!
Ilario 
20 Apr
20 Apr
9:19 a.m.
New subject: [lime-users] 802.11s config
What libremesh version are you using? Where did you get the binaries?
You can check /etc/banner
On 19/04/17 20:46, Ruairi Hickey wrote:
On Wednesday 19 April 2017 19:29:59 IST Ilario
Gelmetti wrote:
--
./p4u
On 04/19/2017 05:25 PM, Ruairi Hickey wrote:
Hi Ilario,
The WAN port is connected to the switch and if that is the only router in
up / or if I connect to that when connecting to SSID libremesh.org I can
connect to the internet.
If I connect to either of the other 2 nodes I cannot connect to the
Internet...
I've attached 2 text files (one for each router with the file contents)
router connected to switch (WAN port) / Internet
router-d94040.txt
router in mesh
router-d94480.txt
Thanks,
Ruairi
(if the attachments get stripped I'll resend with the contents inline..)
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
While the mesh appears to be up and the stations
can see each other
there is no ip connectivity - if a client is connected to the
libremesh.org
via AP node d9:18:6e it can not connect to the internet / outside via AP
d9:44:80.
Hi Ruairi!
Have you plugged an internet connection to a WAN port of your router?
If your router doesn't have a WAN port you will have to configure
another one as WAN (check out /etc/config/lime-example and
http://libremesh.org/docs/changing_network_behavior.html ).
If this doesn't work: can you post the content of /etc/config/network on
your LibreMesh router?
And the output of the "ip address show" commend.
Are there additional steps required to enable
this (it works
out of the box on ad- hoc) ?
No, it should automagically work when you plug the WAN port of the LiMe
router into a LAN port of a router offering a DHCP server and a gateway
to the internet.
Let us know!
Ilario
9:34 a.m.
New subject: [lime-users] 802.11s config
On 19/04/17 20:46, Ruairi Hickey wrote:
On Wednesday 19 April 2017 19:29:59 IST Ilario
Gelmetti wrote:
The link layer seems to work fine in your setup, so the problem is
proably in the mac or ip layer. Please, run the next test and attach the
output:
Run "bmx6 -c originators" to see all nodes in the network.
Run "bmx6 -c links" to see the one-hop nodes
Run "batctl o" to see the layer2 nodes
Run "bmx6 -cp" on the node with Internet connection to see if the tunIn
for sharing Internet is enabled (inet4).
Cheers.
On 04/19/2017 05:25 PM, Ruairi Hickey wrote:
Hi Ilario,
The WAN port is connected to the switch and if that is the only router in
up / or if I connect to that when connecting to SSID libremesh.org I can
connect to the internet.
If I connect to either of the other 2 nodes I cannot connect to the
Internet... While the mesh appears to be up and the stations
can see each other
there is no ip connectivity - if a client is connected to the
libremesh.org
via AP node d9:18:6e it can not connect to the internet / outside via AP
d9:44:80.
Hi Ruairi!
Have you plugged an internet connection to a WAN port of your router?
If your router doesn't have a WAN port you will have to configure
another one as WAN (check out /etc/config/lime-example and
http://libremesh.org/docs/changing_network_behavior.html ).
If this doesn't work: can you post the content of /etc/config/network on
your LibreMesh router?
And the output of the "ip address show" commend.
Are there additional steps required to enable
this (it works
out of the box on ad- hoc) ?
No, it should automagically work when you plug the WAN port of the LiMe
router into a LAN port of a router offering a DHCP server and a gateway
to the internet.
Let us know!
Ilario I've attached 2 text files (one for each router
with the file contents)
router connected to switch (WAN port) / Internet
router-d94040.txt
router in mesh
router-d94480.txt
Thanks,
Ruairi
(if the attachments get stripped I'll resend with the contents inline..)
_______________________________________________
lime-users mailing list
lime-users(a)lists.libremesh.org
https://lists.libremesh.org/mailman/listinfo/lime-users
--
./p4u
10:10 a.m.
New subject: [lime-users] 802.11s config
Hi,
As per banner below, it's
LiMe 16.07 CommunityChaos (16.07 rev.5fbd38f 20160913_2151)
Thanks
Ruairi
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
CHAOS CALMER (Chaos Calmer, r49403)
-----------------------------------------------------
* 1 1/2 oz Gin Shake with a glassful
* 1/4 oz Triple Sec of broken ice and pour
* 3/4 oz Lime Juice unstrained into a goblet.
* 1 1/2 oz Orange Juice
* 1 tsp. Grenadine Syrup
-----------------------------------------------------
___ __ __ _______ __
| |_|__| |--.----.-----.| | |-----.-----| |--.
| | | _ | _| -__|| | -__|__ --| |
|_____|__|_____|__| |_____||__|_|__|_____|_____|__|__|
------------------------------------------------------
LiMe 16.07 CommunityChaos (16.07 rev.5fbd38f 20160913_2151)
------------------------------------------------------
http://libremesh.org
------------------------------------------------------
Ruairi
On Thursday 20 April 2017 11:34:09 IST Pau wrote:
On 19/04/17 20:46, Ruairi Hickey wrote:
On Wednesday 19 April 2017 19:29:59 IST Ilario
Gelmetti wrote:
The link layer seems to work fine in your setup, so the problem is
proably in the mac or ip layer. Please, run the next test and attach the
output:
Run "bmx6 -c originators" to see all nodes in the network.
Run "bmx6 -c links" to see the one-hop nodes
Run "batctl o" to see the layer2 nodes
Run "bmx6 -cp" on the node with Internet connection to see if the tunIn
for sharing Internet is enabled (inet4).
Cheers.
> I've attached 2 text files (one for each router with the file contents)
> router connected to switch (WAN port) / Internet
> router-d94040.txt
>
> router in mesh
> router-d94480.txt
>
> Thanks,
>
> Ruairi
>
> (if the attachments get stripped I'll resend with the contents inline..)
>
>
>
> _______________________________________________
> lime-users mailing list
> lime-users(a)lists.libremesh.org
> https://lists.libremesh.org/mailman/listinfo/lime-users On 04/19/2017 05:25 PM, Ruairi Hickey wrote:
Hi Ilario,
The WAN port is connected to the switch and if that is the only
router in
up / or if I connect to that when connecting to SSID libremesh.org I can
connect to the internet.
If I connect to either of the other 2 nodes I cannot connect to the
Internet... While the mesh appears to be up and the stations
can see each other
there is no ip connectivity - if a client is connected to the
libremesh.org
via AP node d9:18:6e it can not connect to the internet / outside via AP
d9:44:80.
Hi Ruairi!
Have you plugged an internet connection to a WAN port of your router?
If your router doesn't have a WAN port you will have to configure
another one as WAN (check out /etc/config/lime-example and
http://libremesh.org/docs/changing_network_behavior.html ).
If this doesn't work: can you post the content of /etc/config/network on
your LibreMesh router?
And the output of the "ip address show" commend.
Are there additional steps required to enable
this (it works
out of the box on ad- hoc) ?
No, it should automagically work when you plug the WAN port of the LiMe
router into a LAN port of a router offering a DHCP server and a gateway
to the internet.
Let us know!
Ilario
2802
days inactive
2803
days old
lime-users@lists.libremesh.org
6 comments
3 participants
participants (3)
-
Ilario Gelmetti -
Pau -
Ruairi Hickey